• 商品名称：CHT SE3000 电子灌封胶 2KG
• 商品编号：PLTS000902
• 品牌：CHT
• 上架时间：2026-02-24
• 商品毛重：0克
• 材质：聚氨酯
• 一级分类：双组分硅酮

如果您发现商品信息不准确，欢迎电邮纠错。

鉴于国内市场恶性价格竞争考量，本站所有价格均为处理后的虚化价格！如果您对产品系列有切实需求，欢迎电邮询价或致电我们的客服。

24小时快速联系客服...电子邮件: info@plutusat.com ...手机（微信同号）：19941715801 & 13961884175...腾讯QQ：369517302

为了网站安全，我们临时关闭了在线付款模块，客户可以通过同步淘宝旗舰店plutusat.taobao.com网购所需的产品。

.

.

 

SE3000是一款专为电子灌封和封装应用设计的双组分硅橡胶弹性体系统。它能有效抵御化学物质侵蚀、环境污染、机械冲击、振动及撞击损伤。适用于低可燃性要求场景。该固化弹性体可修复，其组分粘度较低，可手动或机械轻松混合。颜色为橙色，重量为2kg（A+B=1+1）。保质期为 12 个月

 

==TDS==

 

This is a 2-component, silicone elastomer system specially designed for electronic potting and encapsulation applications. It offers good protection against chemicals, environmental contamination, mechanical shock, vibration and impact damage. It can be employed in areas where low flammability is a prerequisite. The cured elastomer can be repaired. The component parts have relatively low viscosities and are readily mixed either by hand or machine.

 

这是一种双组分硅酮弹性体体系，专为电子灌封与封装应用而设计。该材料能有效抵御化学品侵蚀、环境污染、机械冲击、振动及撞击损坏，适用于对阻燃性有要求的场景。固化后的弹性体可进行修补操作。其组分粘度相对较低，便于手工或机械混合。

 

IMPORTANT:

 

The‘A’part of product contains the platinum catalyst; great care should be taken when using automatic dispensing equipment. Please ensure that it is not contaminated by residual hydride containing rubber in the dispensing equipment, as curing will result. If in doubt, it’s advised to thoroughly purge the equipment with a suitable hydrocarbon solvent or silicone fluid.

 

重要提示：

 

本产品的A组分含有铂金催化剂，使用自动化点胶设备时需特别注意。请确保设备无含氢橡胶残留物污染，因其接触可能导致固化反应。如有疑虑，建议使用适用的碳氢溶剂或硅油对设备进行彻底清洗。

 

Mixing

 

Both the ‘A’ and ‘B’ parts should be well stirred to ensure the material is uniform and any settlement of the fillers have been remixed.

 

Place the required amount of ‘A’ and ‘B’ parts by weight at the mix ratio shown opposite, in a clean plastic or metal container of approximately 3 times their volume, and mix until the colour of the mixture is uniform. For best results, we recommend degassing. Degas by intermittent evacuation, the larger volume of the mixing vessel helps prevent overflow during this operation. In case of automatic dispensing with static mixing head, the two components should be degassed before processing. Recommended vacuum conditions are 30-50 mbar intermittently over 5-10 minutes. Cast the mixture either by gravity or pressure injection.

 

混合操作

 

请将A、B两组分分别充分搅拌，确保材料均匀且填料沉降物已重新混合均匀。

 

按背面标注的混合比例称取所需重量的A、B组分，置于容积约为混合物三倍体积的洁净塑料或金属容器中，持续混合至混合物颜色均匀。为达到最佳效果，建议进行脱气处理。采用间歇抽真空方式脱气，使用较大容积的混合容器有助于防止操作过程中物料溢出。若使用配备静态混合头的自动化点胶设备，两组分需在加工前分别脱气。推荐真空条件为30-50毫巴，间歇抽真空5-10分钟。可采用重力浇注或压力注射方式灌入混合料。

 

Inhibition of Cure

 

Great care must be taken when handling and mixing all addition cured silicone elastomer systems, ensuring that all the mixing tools (vessels and spatulas) are clean and constructed in materials which do not interfere with the curing mechanism. The cure of the rubber can be inhibited by the presence of compounds of nitrogen, sulphur,phosphorus and arsenic; organotin catalysts and PVC stabilizers; epoxy resin catalysts and even contact with materials containing certain of these substances e.g. moulding clays, sulphur vulcanised rubbers, condensation cure silicone rubbers, onion and garlic.

 

固化抑制说明

 

在处理和混合所有加成型硅酮弹性体体系时需格外谨慎，确保所有混合工具（容器和刮刀）清洁且由不会干扰固化机制的材料制成。氮、硫、磷和砷的化合物；有机锡催化剂和聚氯乙烯稳定剂；环氧树脂催化剂，甚至与含有某些上述物质的材料（如造型黏土、硫硫化橡胶、缩合固化硅橡胶、洋葱和大蒜）接触，均可能抑制橡胶的固化。

 

Curing Conditions

 

The data offers a guide to the rate of cure at various temperatures. Mixing of the components at temperatures between 15 and 25°C is recommended to ensure adequate pot life for degassing and handling. The pot life can be extended to several hours by chilling the components before mixing. 

 

固化条件

 

该数据为不同温度下的固化速率提供参考。建议在15至25摄氏度之间混合组分，以确保有足够的操作时间进行脱气和后续处理。若需延长操作时间，可在混合前对组分进行冷藏处理，使操作期延长至数小时。

 

* It is absolutely important to check the compatibility in preliminary tests if unknown substrates are used.

 

* 若使用未知基材，务必通过初步测试进行相容性验证，这一点至关重要。

 

Safety

 

Please observe our EC safety data sheets and the safety remarks on our container labels when handling our products. The dangerous goods regulations and the accident prevention regulations of the professional associations must be particularly observed. Keep the EC safety data sheet of the applied product at hand since it provides you with useful instructions for the safe use and disposal of the product as well as for actions to be taken in case of accidents.

 

安全须知

 

在处理本产品时，请遵守我们的EC安全数据表及容器标签上的安全提示。尤其需遵循危险品管理规定及行业协会颁布的事故预防规程。请务必备妥所用产品的EC安全数据表，该文件提供了关于产品安全使用、废弃处置以及事故发生时的应急处理等重要指导信息。

 

 

商品属性
[材质]	聚氨酯
[一级分类]	双组分硅酮

用户评论(共0条评论)

• 暂时还没有任何用户评论

总计 0 个记录，共 1 页。 第一页 上一页 下一页 最末页

⚠️ 评论功能临时关闭

为了防止SQL注入等安全风险，我们暂时关闭了在线用户评论功能。如果您有任何产品咨询或购买需求，请通过以下方式直接联系我们：

📞 电话/微信：19941715801 或 13961884175

📧 电子邮件：info@plutusat.com

💬 腾讯QQ：369517302

🛒 淘宝旗舰店：plutusat.taobao.com

给您带来的不便敬请谅解，感谢您的理解与支持！